Skip to main content

Elastomers.

Elastomers.

The natural or synthetic polymers which have elastic properties is called Elastomers.
For example; rubber. 

Origin of rubber.

The word 'rubber' is derived from its early application i.e the property of weeping tree to rub out pencil writing. Many materials were impregnated with rubber to make it waterproof. However, the performance of rubber was still quite poor because it was gummy at the time and fluctuation in temperature cause change in products.
It was the year 1839, when Goodyear accidentally discovered the vulcanisation of rubber, which makes the rubber elastic and it can keep or preserve its characteristics with fluctuation in temperature.

Types.

There are two types of rubber.
1) Natural rubber: Natural rubber is produced from latex i.e the milky emulsion extracted from rubber tree or other plants, where the coagulated latex is transform into sticky, soft and plastic substance (Crude rubber) and then Vulcanised (Cured). The rubber is composed of polyisoprene molecule. Rubber serve as an adhesives. The natural rubber has the following structural formula in which there is alternate double bond on every carbon atom.
Natural rubber.
The natural rubber when treated with proton donor such as sulphuric acid etc gives cyclised rubber. Natural rubber when treated with chlorine gives chlorinated rubber.
2) Synthetic rubber: Synthetic rubber are elastomers which have properties similar to natural rubber. They are composed of material similar to natural rubber. Some synthetic rubber are polybutadiene, butyl rubber, neoprene and silicone etc.

Comments

Post a Comment

Popular posts from this blog

Determination of molecular weight of polymers by viscosity method.

Determination of molecular weight of polymers by viscosity method. It is a simple method for determining the molecular weight of polymers. Addition of polymers in the solvent increases the viscosity of the solvent, due to introduction of inhomogeneities by the polymers. If η₀ is the viscosity of the solvent and η is the viscosity of the solution at the same temperature, then the relative viscosity is given by Relative viscosity. Specific viscosity:  It is defined as the relative increase in viscosity and is given as Specific viscosity. Reduced viscosity: It is defined as the relative increase in viscosity per unit concentration (C) of polymer and is given as Reduced viscosity. Intrinsic viscosity: The reduced viscosity is dependent on concentration (C). If a graph is plotted between  reduced viscosity vs concentration then the extraplotation value when C=0 is called intrinsic viscosity. Intrinsic viscosity. Graph of reduced viscosity vs concentr
2 comments
Read more

Determination of molecular weight by Light scattering method.

Determination of molecular weight by Light scattering method. Due to big size macromolecules in solution, turbidity is produced. The light rays get scattered, when pass through macromolecule solution due to turbidity. The turbidity T is given by Where I₀ is the intensity of incident light. Iₜ is the intensity of transmitted light after passing through a solution of length l.        In case of proteins or higher polymers the turbidity is small and is determine from the intensity of light scattered at 90° to the beam. This can be done by using a simple photometer as shown in figure below. Turbidity increase with increase in concentration as well as molecular weight. The Turbidity is related to molecular weight by the equation given by Debye. Hc/T=1/M+2Bc Where B is second virial coefficient and H is a constant. If we plot a graph between Hc/T vs c we get a straight line with intercept 1/M. Thus This curve was plotted by Zimm, so is called Zimm's Curve. Thus the c
Post a Comment
Read more

Polypropylene (PP)

Polypropylene (PP). Polypropylene (PP) is also known as polypropene. Polypropylene is made from the polymerisation of propylene gas in the presence of Zeiglar Natta catalyst or metallocene catalyst. Polypropylene. Thus propene (or propylene) is the monomer of polypropylene. Polypropylene is a highly flammable material. It is sensitive to microbial attacks, such as bacteria and mold. It exhibits excellent resistance to diluted and concentrated acids, alcohols and bases. Polypropylene is used to make lunch boxes, margarine containers, yogurt pots, syrup bottles etc. Disposable syringes is the most common medical application of polypropylene. Polypropylene rope and twine are very strong and moisture resistant very suitable for marine applications. Polypropylene, highly colorfast, is widely used in manufacturing carpets, rugs and mats. Uses of Polypropylene. Questions on polypropylene; Q1) What is polypropylene? Ans) Polypropylene is a polymer of propylen
Post a Comment
Read more